articles, DYNACORD MIXER CMS 1000, DYNACORD MIXER CMS 1600, DYNACORD MIXER CMS 2200, DYNACORD MIXER CMS 600, DYNACORD PM 1600, DYNACORD PM 2200, DYNACORD PM 3 1000, DYNACORD PM 3 600, DYNACORD PM 502, Hardware equipment, Sound mixer, Voice

Graphic equalizer

اکولایزر گرافیکی

Graphic equalizer

Well, as far as I know we have three types Equalizer . One of them is the graphic equalizer.

As I explained in previous articles, the parametric equalizer is made up of multiple volumes.

And as the name suggests, you can get the sound you want by setting a number of parameters across these volumes.

In graphic equalizers, Equalization The sound is performed more accurately.

And indeed, you can tell that your hands are more open to equalize the sound.

This type of equalizer was commonly found on older radios, but has now been replaced by digital equalizers.

The equalizer you see in home and car audio recorders is a digital equalizer.

What is a graphic equalizer?

Graphic equalizers usually contain 10 to 15 audio channels.

It goes without saying that each of these channels is stereo.

Usually each channel of these graphic equalizers can be changed from 10 to 15 decibels (db).

Dinacor The graphic equalizers include 11 channels.

Each of these channels can be increased or decreased by 10 dB.

In previous versions, the number of channels was 10.

Powermixer 502 Dynacord The number of channels of the graphic equalizer is 7 toast.

Usually in equalizers, the high frequency (treble – bass sound) is on the right, the middle frequency (mid-mid) is in the middle and the low frequency (bass – bass) is on the left.

Dynacord mixer graphic equalization

Work with the graphic equalizer

High frequency

The 12Khz frequency channel includes the high frequency which determines the following sound in the output sound.

The sound gets lower as the 12Khz frequency decreases.

High frequency range (high – low)

The frequency range from 6.3Khz to 2.5Khz is the range of the following frequencies up to the mid frequencies.

This range includes the frequencies that make up the following sound.

You can make the output sound clearer by amplifying this frequency range.

Be careful not to overdo this graphic equalizer.

Increasing this range will result in feedback or whistling in the bands.

especially when the rate Volumes (Hi) The parametric equalizer is high.

Range of mid (mid) frequencies

The 1.6Khz to 630hz frequency range is the mid-frequency range of audio.

This range is used to erase and jam the sound.

Normally I always try to keep this range of sounds below the high and low frequencies.

Blocking the channels in this area causes the sound to become hoarse or nasal.

Low frequency range (bass – bass sounds)

The frequency range from 400 hz to 125 hz is the range of frequencies in between the bass frequency.

As this range increases, the volume increases or, in a simpler interpretation, the volume of the bass increases.

The lower the channels associated with this range, the more empty the sound becomes and the more volume it loses.

Low frequency

The 63hz frequency channel contains the low frequency which determines the bass sound in the output sound.

As this channel increases, the sound becomes louder and louder and as this frequency decreases, the sound becomes hollow.

Setting the equalization

The important thing here is that I type Equalize We don’t have a single.

We don’t have an equalizer to say this is the best and we don’t have a better equalizer.

You need to adjust the equalizer channels according to the player’s voice and the sound you want to output.

Of course, the type of sound you make also depends on the following factors:

  • Microphone type
  • Microphone EQ type (in some microphones)
  • Parametric EQ type
  • Block
  • Equalize the bands (only in active bands)
  • and especially the singer’s voice

Knowledge of sound genres depends on your personal experience.

Apply graphic equalizer to outputs

mixer as Dynacord You will be able to determine which of your outputs your equalizer will be applied to.

Obviously, there aren’t many open hands on all releases.

You can only specify a graphic equalizer to apply to the following three outputs.

If under the graphic equalizer in the mixers Dynacord Take a look, you see there are three lights.

“Graphic Eq To” is visible above these lights.

These lights determine which output of your device’s graphic equalizer is applied.

That is, if the equalizer is assigned to the master, the green light will turn on.

and if the equalizer goes to channels Mon (Mon 1 / Mon 2) Assign, yellow lights turn on.

I stress once again that the graphic equalizer outputs are never applied to the following outputs:

Frequently Asked Questions

Some of Rajab’s friends have asked a number of questions in this article, which I think I need to explain in this section.

One thing to note here is that reading this section is not part of the tutorial and I may need to re-explain the past.

Graphic equalizer setting

One of the most important parts of mixing and adjusting the sound is the problem of sound equalization.

The sound equalizer is very important in live performances and mixing. There are many benefits to equalizing the sound, including:

Separation of frequency domains from each other

For example, in concerts, a separate equalization is applied to each of the microphone outputs so that each microphone does not pick up the sound of other instruments and feed them into the system.

There are several advantages to this type of sound separation:

First, you can easily control the sounds in the live stream.

Secondly, for recording, the sound is recorded separately and is easier to mix.

Third, applying effects to any sound is easier and more accurate.

Amplify the sound

One of the most important uses of an equalizer is to amplify the sound.

For example, you can mute or lower the singer’s voice, as you are amplifying different frequencies of the singer’s voice.

Prevent sound distortion

Sadla has several reasons for distortion, one of which is improper sound equalization.

If you equalize the sound input to the mixer based on the equalization of each band, the bands are less likely to whistle or distort the sound during live broadcast.

Adjusting the sound equalizer, whether graphic or parametric, requires experimental knowledge.

No matter how much you read about EQ types, I don’t think you will learn, or rather become a pro, unless you do it yourself.

Adjust the Dinacord equalizer

The equalizer setting of the Dinacor device is not very different from other analog devices.

You just have to pay attention to the fact that in both Dynacord mixers and other mixers, changing one millimeter of each of these bands (equalizer power supply) is important and affects the sound output.

So be careful in equalizing the sound and especially in changing the equalizer while playing the sound. Especially when playing audio because the changes in the sound are very noticeable right now.

Setting the Dinacord 1000 equalizer

Dynacord Model 1000 has 11 bands for graphic equalizer adjustment.

6 lines of sound from this mixer have 4 volumes of parametric equalizer and 4 lines of sound from this mixer have 3 volumes of parametric equalizer.

Setting the Dinacord 600 equalizer

The old Dynacord 600 model has 7 numbers and the new Dynacords 600 model has 9 bands to adjust the graphic equalizer.

This device has 8 sound lines or sound lines, all of which have 3 parametric EQ volumes.

There is no Khz volume in the Dynacord 600’s parametric equalizer and it is not possible to define any variable values ​​to define the Mid volume.

In other words, Mid is always at a certain kHz.

Leave a Reply

Your email address will not be published. Required fields are marked *